The press-in method describes the static pressing-in of components, tool parts, or auxiliary elements into an environment made of concrete, masonry, steel, or rock. Unlike impact or vibration methods, it uses controlled, continuous pressing forces. In construction, deconstruction, and in tunnel and rock-mechanics settings, it is used when vibrations, noise, and flying fragments must be avoided. In combination with hydraulic systems and tools—such as rock wedge splitter and concrete splitter or concrete demolition shear from Darda GmbH—the press-in approach enables material-friendly, precise, and plannable work steps in concrete demolition, building gutting, rock excavation, or natural stone extraction.
Definition: What is meant by the press-in method
The press-in method is understood as a statically guided joining or pressing-in of elements into a carrier medium. The spectrum ranges from press fits (interference fits) in mechanics, to pressing in sheet pile walls and piles, through to the hydraulic press-in of wedges into predrilled core holes to generate a controlled split in rock or concrete. Characteristic features are defined pressing forces, continuous force transmission without impact impulses, and a reproducible process. In practice, hydraulic cylinders are hosed to suitable hydraulic power pack units and controlled via pressure stages, valves, and pressure gauges.
Operating principle and sequence at a glance
Press-in transfers force over an area or line onto the component. In splitting applications, pressure is introduced via wedge or spreading elements onto the borehole flanks; for press fits, a targeted interference is used; for piles or sheet piles, the reaction force is routed into the subsoil via bracing or counterweight. The generic sequence:
- Survey of the material (concrete compressive strength class, reinforcement density, rock joints) and definition of the pressing strategy
- Marking and creation of the geometry (e.g., drilling patterns for splitting cylinders, guide rails for built-in component)
- Setup of the hydraulics with pressure- and flow-matched sizing of the hydraulic power pack
- Stepwise pressing-in with intermediate measurements (force, stroke, optionally noise emission and ground vibration monitoring)
- Control of results (split progress, set, positional accuracy), re-pressing or releasing
- Follow-up work: demolition, cutting, separating, or securing components with suitable tools such as concrete demolition shear, attachment shear or cutting tool
Process variants and typical application pictures
The press-in method appears in different facets that share the same basic principle—static force introduction:
- Hydraulic pressing of wedges into boreholes for crack initiation and controlled widening; basis for splitting concrete and natural stone with rock wedge splitter and concrete splitter
- Press fits in assembly and maintenance (e.g., bushings, pins, knife bodies); relevant for servicing tool heads, cutting jaws, or bearing points of concrete demolition shear, steel shear, and attachment shear
- Static pressing-in of sheet piles, piles, or beams (press-in method) in sensitive environments with strict vibration limits
- Pressing-in of built-in parts, anchor sleeves, and connectors into prepared openings or seats
Areas of application at a glance
Concrete demolition and special demolition
Where impact tools are not permitted, components can be separated by pressing in splitting wedges. After the split, concrete demolition shear take over controlled removal of remaining sections, trimming ribs, and exposing reinforcement. This enables low-vibration deconstruction in densely built urban environments.
Building gutting and cutting
In selective dismantling of existing buildings, press-in is used to release embedded parts or to introduce new temporary anchorage points. Afterwards, attachment shear, cutting tool, or steel shear cut lines, sections, and sheet metal, while concrete demolition shear remove residual concrete.
Rock excavation and tunnel construction
In rock and shotcrete, splitting lines can be defined via drilling patterns. By pressing the wedge system into the boreholes, plannable separation joints are formed. Handling of the resulting blocks depends on the project—using steel shear for support elements or cutting tool for mixed materials.
Natural stone extraction
Gentle extraction of blocks in quarries relies on defined split planes. By pressing in the wedges, natural joint systems are exploited and smooth fracture surfaces are achieved, simplifying further processing.
Special applications
For work on tanks, vessels, or in potentially explosive atmospheres (ATEX zone), low-vibration methods are required. Static pressing-in of auxiliary elements, releasing press fits, and subsequent separation with cutting torch and cutting tool reduces sparking and structural excitation.
Tool and system selection
Reliable press-in requires hydraulics, tool geometry, and material to match:
- Hydraulic power pack: Working pressure and flow must match cylinder area and the planned cycle rhythm. Allow reserves for cold starts and long hydraulic hose line runs.
- Rock wedge splitter and concrete splitter: Wedge size, borehole diameter, and split set height must be aligned to strength class, aggregates, and reinforcement content.
- Concrete demolition shear: Jaw geometry and opening width influence the clean nipping of concrete edges after splitting; check cutting edge condition regularly.
- Steel shear, attachment shear, cutting tool: For mixed demolition with metal content; hardness and toughness of the materials determine the cutting sequence.
Design of pressing forces and drilling patterns
The required pressing force results from material strength, contact geometry, and friction. In concrete, aggregate, moisture, and reinforcement ratio influence the splitting behavior; in natural stone, joint orientation and grain structure are decisive. Conceptual principles:
- Drilling patterns parallel to planned separation joint; observe edge distance
- Sequence of pressing diagonally or alternating to exploit stress redistribution
- Combination of pre- and post-pressing to control the split-progress curve
- Measurement of stroke and pressure to document the force–displacement relationship
Advantages and limitations
Static press-in is low vibration levels, low-noise, and well documentable. It is suitable for sensitive environments and complex existing structures. Limits appear with extremely high-strength sections, high steel content, or insufficient counterbearing of reaction forces. Here, adapted drilling patterns, relief cut, or the combined use of concrete demolition shear and steel shear help.
Safety and environmental protection
Occupational safety has priority. Pressing forces may only be applied after complete support; wedge and borehole areas must be secured against access (e.g., safety fence). Personal safety equipment, shields against fragments, and clear hand-signal communication are mandatory. Environmental aspects such as avoiding leaks, noise reduction measures, and compliance with local vibration limits must be considered case by case. Legal requirements can vary by location and should be checked in advance.
Quality assurance and documentation
Traceable documentation includes pressing pressures, cycle times, displacement measurements, and visual inspections. Test certificates for borehole diameters, anchor lengths, or split faces and photo logs facilitate acceptance. For recurring work, calibration of the pressure measurement on the hydraulic power pack and regular condition checks of wedges and cutting edges are recommended.
Typical sources of error and how to avoid them
- Inappropriate borehole geometry: pay attention to diameter, depth, and cleanliness
- Pressure increase too fast: press in steps, wait for spring-back
- Underestimated reinforcement density: plan pre-separation with concrete demolition shear
- Unfavorable joint orientation in natural stone: verify orientations in advance with test drilling
- Overheating of the hydraulics: provide sufficient cooling and breaks in the cycle plan
Practice-oriented planning
For economical results, an integrated approach is recommended: site walkdown, material testing, selection of the press-in method, design of the hydraulics, definition of drilling patterns, combined use of rock wedge splitter and concrete splitter with concrete demolition shear and complementary tools, plus seamless documentation. This yields reproducible workflows in concrete demolition and special deconstruction, building gutting and cutting, rock excavation and tunnel construction, natural stone extraction, and special applications.