The foundation base is the decisive contact surface between the structure and the subsoil. Its proper execution determines the load-bearing capacity, serviceability, and durability of foundations and floor slabs. In practice this concerns not only new construction, but also concrete demolition and special demolition in existing buildings: when exposing, adapting, or removing foundations, foundation bases must be specifically created, protected, or selectively deconstructed. Hydraulic tools from Darda GmbH are used in both planning and execution—such as a concrete demolition shear for removing foundation edges or hydraulic rock and concrete splitters for controlled opening of massive foundations or for leveling exposed rock faces in rock demolition and tunnel construction.
Definition: What is meant by foundation base
The foundation base is the underside of a shallow foundation or the plane through which loads from the structure are transferred to the load-bearing ground. For strip, isolated foundations, and floor slabs, it is the base of the foundation; for deep foundations, it functionally corresponds to the bearing zone (for example, the pile toe). The excavation pit base (lowest point of the excavation prior to creating the subgrade) and the subgrade or prepared bedding (e.g., a blinding layer of lean concrete or compacted gravel) must be distinguished from the foundation base. Key requirements for the foundation base are sufficient load-bearing capacity, flatness, slope and elevation, capillary break and frost protection, as well as defined roughness or tensile bond strength where concrete members are to be bonded monolithically on top.
Structure and requirements for the foundation base
The build-up of the foundation base depends on the subsoil, structural loads, and usage requirements. The objective is uniform load transfer without harmful settlements. Depending on the situation, the layer sequence includes a load-bearing subgrade, a capillary-breaking and frost-resistant layer (e.g., gravel/chippings), an optional geotextile, a blinding layer, and, where required, waterproofing. The base must be produced so that flatness tolerances, compaction levels, and water management are met.
Layer sequence and material selection
Common are compacted mineral base layers with adequate grading, a capillary barrier to prevent moisture rise, and, if needed, a blinding layer to create a clean, even bedding. In cohesive soils, ground improvement (lime/cement) or soil replacement may be necessary; on rock, adequate roughening/leveling for load-bearing performance is decisive.
Load-bearing capacity and deformation
The foundation base must enable verification against bearing failure and excessive settlements. This includes adequate compaction (controlled, for example, with a load plate test or a dynamic load plate) and a homogeneous stiffness distribution to avoid stress concentrations.
Frost and moisture protection
In frost-susceptible ground, the foundation base lies below the relevant frost penetration depth or receives constructive frost protection. A capillary-breaking layer reduces moisture and prevents frost heave. Slopes and drainage ensure controlled water discharge.
Surface quality and flatness
For monolithic bearing of foundations, defined flatness and, where subsequent concreting follows, a suitable surface texture must be ensured. Local weakening (e.g., softening due to rain) must be avoided; installation should take place as soon as possible after approval.
Construction of the foundation base on soil and rock
Execution starts with proper excavation works, reaching the target elevation, producing the subgrade, and providing the necessary compaction and load-bearing verifications. On exposed rock, the base is produced by knocking off protrusions, removing weathered zones, and leveling. In sensitive environments—such as near existing buildings—low-vibration methods are recommended. Hydraulic splitter from Darda GmbH enable controlled splitting of rock noses or massive foundation sections when a planar bearing surface is needed. In rock excavation and tunnel construction or when creating foundation benches, vibrations and noise can thus be minimized—an advantage especially in special demolition (e.g., in densely built areas).
Work in groundwater
If the foundation base lies in or near groundwater, groundwater lowering, filter wells, or sealing measures must be planned. A blinding layer can serve as a working and protective layer. Measures to prevent piping and to secure the excavation walls are to be defined project-specifically.
Subsoil improvement
If load-bearing capacity is insufficient, soil replacement, injections, vibro methods, or binder stabilization are used. The goal is homogeneous stiffness of the foundation base and the limitation of settlements.
Quality assurance and verification
For acceptance of the foundation base, elevation, flatness, compaction, material properties, and water management are documented. Pre-tested materials, in-process compaction self-checks, and spot checks (e.g., dynamic load plate, plate load test, particle size distribution) form the basis. A swift continuation of work protects the base from softening and erosion.
Surveying and tolerances
Height control and marking of foundations must be checked before concreting or installing the blinding layer. Flatness requirements must be defined for the specific project and monitored.
Foundation base in existing structures: exposing, adapting, deconstruction
In conversions or refurbishments, the existing foundation base is often exposed, locally lowered, or partially removed. Work must proceed in stages to avoid endangering stability. In concrete demolition and special demolition, hydraulic, low-vibration methods have proven themselves: a concrete demolition shear from Darda GmbH cuts concrete selectively and enables targeted removal of foundation edges and tops, while a hydraulic splitter splits massive blocks internally to guide tensile cracks in a controlled manner. Hydraulic power units supply the tools with energy; hydraulic shear, multi cutters, and steel shear cut reinforcement and embedded parts. In this way, utility trench excavation, underpinning, or openings can be realized with minimal intervention—an essential prerequisite in building gutting and concrete cutting and when working in sensitive environments.
Selective deconstruction of foundations
A typical sequence is: delineate (saw/cut), relieve loads, pre-break with a concrete demolition shear, controlled splitting of thick sections, then separation of concrete and steel. This approach reduces vibrations, facilitates material separation, and protects adjacent components.
Adjusting the foundation base for repurposing
If the foundation base is to be locally lowered or raised, structural implications must be checked. An additional blinding layer of lean concrete, a capillary-breaking layer, or local ground improvement may be required. Interventions are to be carried out in sections with suitable securing.
Safety and environmental aspects
Work on the foundation base requires special attention to excavation safety, edge stability, and groundwater control. Low-vibration methods reduce risks to neighboring buildings and utilities. Dust and noise reduction—such as dust suppression and noise reduction measures—protection against water contamination, and orderly disposal and recycling (of reinforcing steel) are part of best practice. Requirements from standards and permits must be considered on a project-specific basis.
Avoiding common mistakes
- Inadequate compaction of the subgrade leading to subsequent settlements.
- Working on a softened base without a protective or blinding layer of lean concrete.
- Lack of frost and moisture protection with capillary rise and frost heave.
- Uncontrolled removal on rock with overbreak and uneven bearing.
- Insufficient flatness, causing stress concentrations in the foundation.
- Unplanned cutting of reinforcement or embedded parts during deconstruction.
- Missing documentation of elevation and compaction values.
Practical tips for planning and execution
- Early subsoil investigation and definition of required verifications.
- Clearly define acceptance criteria for flatness, compaction, and water management.
- Prioritize low-vibration methods: plan concrete demolition shear and hydraulic splitter for selective removal and splitting.
- Organize logistics and accessibility for hydraulic power pack and tool changes.
- Provide trial areas for splitting techniques on massive components, e.g., a field trial/test.
- Use weather windows; protect or build over the foundation base immediately after approval.
- Carry out surveying and photo documentation for acceptance of the foundation base.
- Early coordination of openings, utility routing, and drainage.
Applications in the deployment areas
In concrete demolition and special demolition, safe handling of the foundation base determines the construction process: selective opening of foundations with a concrete demolition shear and controlled splitting with a hydraulic splitter reduce vibrations. In building gutting and concrete cutting, the base is locally adjusted to enable utility routing or underpinning. In rock excavation and tunnel construction, the leveled rock bearing forms a load-bearing bench—low-vibration splitting of rock noses proves its worth here. In natural stone extraction, a flat, stable bearing surface underpins safe extraction and transport; splitting technology allows precise preparation. In special demolition—for example, in facilities with sensitive surroundings—quiet, low-emission hydraulic methods from Darda GmbH help create or adapt the foundation base without blasting works and with minimal impact.