{"id":19707,"date":"2025-12-09T15:24:11","date_gmt":"2025-12-09T14:24:11","guid":{"rendered":"https:\/\/www.darda.de\/?page_id=19707"},"modified":"2026-05-15T17:56:03","modified_gmt":"2026-05-15T15:56:03","slug":"formwork-anchor","status":"publish","type":"page","link":"https:\/\/www.darda.de\/en\/knowledge\/formwork-anchor","title":{"rendered":"Formwork anchor"},"content":{"rendered":"<div class=\"wissen-inhaltsbereich\">\n<p>Formwork anchors are central components in concrete construction: They hold opposing formwork elements in position during concreting, secure the spacing, and transfer fresh concrete pressure. Over a structure&#8217;s lifecycle they concern designers, contractors, and deconstruction teams alike &#8211; from selection and design to later remediation or selective deconstruction. In many existing structures, remaining anchor rods, sleeves, and cones influence strategies for concrete demolition and special demolition. Tools such as <strong>concrete pulverizers<\/strong> or <strong><a href=\"https:\/\/www.darda.de\/en\/product-overview\/hydraulic-rock-and-concrete-splitters\">hydraulic rock and concrete splitters<\/a><\/strong> enable controlled, low-vibration methods in these situations and facilitate separation of concrete and steel. Clear documentation of anchor layouts supports inspection and deconstruction planning and reduces rework.<\/p>\n<h2>Definition: What is meant by a formwork anchor?<\/h2>\n<p>A formwork anchor is a detachable or permanent connection between two opposing formwork faces that ensures the required spacing of the formwork parts and takes up the resulting forces from fresh concrete pressure. Typically, formwork anchors consist of an anchor rod with a robust thread, anchor plates or anchor points with cones on both sides, spacers or sleeves, and corresponding closures. After the concrete has hardened, anchors &#8211; depending on the system &#8211; are partially removed, cut off flush, or remain as built-in components in the member and are closed off at the surface. In practice, the term is also used for <em>form ties, tie rods, or formwork ties<\/em>, which follow the same functional principle.<\/p>\n<h2>Structure, components and operating principle<\/h2>\n<p>In practice, a formwork anchor system is composed of several coordinated components. The core function is to secure the spacing of the formwork and to transfer the transverse forces that arise during concreting in a controlled manner into the formwork facing or into the formwork girders. Material choices range from unalloyed steels to corrosion-resistant or non-metallic solutions where residual metal is undesirable.<\/p>\n<h3>Typical components<\/h3>\n<ul>\n<li>Anchor rod with a robust, site-ready thread (e.g., trapezoidal thread in common diameters); material selection ranges from unalloyed steel to corrosion-resistant variants. For recurring use, thread protection and inspection of wear are essential.<\/li>\n<li>Anchor sleeve or spacer to ensure the defined wall cross-section and to control the ingress of cement paste. Where applicable, sleeves limit laitance penetration and improve subsequent closure quality.<\/li>\n<li>Anchor cones and finishing cones for clean anchor points, defined breakout after stripping, and visual requirements (exposed concrete) where applicable. Cones also define the reproducible recess geometry for later sealing.<\/li>\n<li>Counterplates with nut or tensioning mechanism to clamp the anchor with frictional engagement. Bearing faces must be sized to limit local compressive stresses in the formwork skin.<\/li>\n<li>Closure systems for the anchor holes (cementitious mortars, resins, cone plugs, sealing washers where increased watertightness is required). Compatibility between closure materials and surrounding concrete is decisive for durability.<\/li>\n<\/ul>\n<h3>Operating principle<\/h3>\n<p>During concreting, the hydrostatic fresh concrete pressure acts on the formwork faces. This load is short-circuited via the anchors as tensile force between the opposing sides of the formwork. After hardening, the external anchor components are released; depending on the system, the inner part (e.g., sleeve, cone) remains in the member. Anchor points that appear at the surface are filled, pressure-grouted, or closed with cones, particularly where increased watertightness or exposed concrete requirements apply. Pour rate, temperature, and concrete consistency influence peak forces and must be reflected in the chosen anchor capacity.<\/p>\n<h2>System variants and selection criteria<\/h2>\n<p>The choice of system is based on load level, wall thickness, surface requirements, watertightness, and the intended approach during deconstruction. Additional drivers include reuse cycles of anchor rods, the targeted emission level during selective demolition, and the repair concept for visible surfaces.<\/p>\n<h3>Common variants<\/h3>\n<ul>\n<li>Continuous anchor rods with clamping on both sides: high flexibility, simple installation, partial removal or flush cutting depending on specification.<\/li>\n<li>Sleeve systems with removable rods: reduce steel remnants in the member and simplify later treatment of anchor points.<\/li>\n<li>Cone systems for exposed concrete: defined, recurring anchor patterns; cleanly removable and closable after stripping.<\/li>\n<li>Special solutions with increased watertightness requirements: additional sealing elements, sealing washers, or multi-stage closure concepts for waterproof structures.<\/li>\n<li>Non-metallic or low-metal content solutions: minimize residual metal in the cross-section to ease future selective demolition and reduce corrosion risks in aggressive environments.<\/li>\n<\/ul>\n<h3>Selection criteria from practice<\/h3>\n<ul>\n<li>Fresh concrete pressure and formwork heights determine the required anchor capacity and quantity.<\/li>\n<li>Corrosion protection and durability, especially if anchor parts remain in the concrete.<\/li>\n<li>Deconstruction concept: The less metal in the cross-section, the easier the separation in selective demolition using concrete pulverizers or rock and concrete splitters.<\/li>\n<li>Surface requirements (exposed concrete, grid pattern, reprofiling depth).<\/li>\n<li>Watertightness and the sealing concept for anchor points in water-exposed members.<\/li>\n<li>Accessibility and reuse: Handling space for nuts and plates, target number of reuse cycles for rods and hardware.<\/li>\n<\/ul>\n<h2>Design, load path and boundary conditions<\/h2>\n<p>Formwork anchors are designed for tension; governing parameters include fresh concrete pressure, formwork height, concreting rate, temperature, and concrete viscosity. Additionally, edge distances, wall thicknesses, and formwork stiffness influence the required number and arrangement of anchor points. The load path comprises tensile forces in the rod, bearing under plates or cones, and local compression in the formwork facing.<\/p>\n<h3>Planning aspects<\/h3>\n<ul>\n<li>Determination of fresh concrete pressure according to recognized engineering practice.<\/li>\n<li>Specification of anchor spacing in line with wall thickness, girder grid, and desired surface pattern.<\/li>\n<li>Verification of anchor components including cones and bearing faces.<\/li>\n<li>Consideration of exposed concrete classes and tolerances for recurring anchor patterns.<\/li>\n<li>Definition of acceptance criteria: permissible imprint, recess tolerances, and closure material performance (e.g., pull-off strength, watertightness).<\/li>\n<\/ul>\n<p>Design information should always follow current standards and guidelines as well as manufacturer specifications. Concrete designs are project-specific and performed by qualified parties. Where anchor remnants are intended to remain, durability and serviceability checks for the surrounding concrete cover are included.<\/p>\n<h2>Installation, sealing and surface quality<\/h2>\n<p>Correct installation of formwork anchors determines not only the formwork&#8217;s structural safety but also the subsequent watertightness and appearance of the concrete surface. Mock-ups for exposed concrete surfaces help validate cone geometry, closure sequence, and color matching before serial execution.<\/p>\n<h3>Installation notes<\/h3>\n<ul>\n<li>Accurate alignment of the anchors in the formwork plane; avoid skewing.<\/li>\n<li>Tight cone and sleeve interfaces to prevent washout and honeycombing.<\/li>\n<li>Controlled release after hardening; defined removal of cones.<\/li>\n<li>Closure of anchor points with suitable mortars or plugs; coordinated sealing concept for water-exposed members.<\/li>\n<li>Clean, bondable substrate preparation in recesses; observe curing and protection of repair materials to achieve rated performance.<\/li>\n<\/ul>\n<h3>Surface appearance<\/h3>\n<p>Anchor points shape the appearance of exposed concrete surfaces. A uniform grid and cleanly formed cones and closures are decisive. For representative members, anchor positions are therefore coordinated early and aligned with the formwork planning. Consistent batching, release agents, and stripping times further reduce visible scatter at closure areas.<\/p>\n<h2>Formwork anchors in existing structures: impact on deconstruction and remediation<\/h2>\n<p>Anchor components often remain in existing walls, slabs, or shafts. These steel parts influence the choice of deconstruction methods. For selective concrete demolition and special demolition, methods that specifically separate steel and concrete or release components with low vibration are suitable. Prior scanning with suitable methods (e.g., reinforcement locators, radar) reduces unforeseen findings and guides the choice of tool and access strategy.<\/p>\n<h3>Low-vibration separation and deconstruction methods<\/h3>\n<ul>\n<li><strong>Concrete pulverizers<\/strong>: Grabbing, crushing, and downsizing concrete while simultaneously exposing anchor rods, which are then cut with steel shears or Multi Cutters.<\/li>\n<li><strong>Rock and concrete splitters<\/strong>: Create controlled cracks along anchor axes or around anchor cones; particularly useful in sensitive environments (gutting, monument preservation, vibration-sensitive plants).<\/li>\n<li>Steel shears and Multi Cutters: Cold-cutting of anchor rods, stirrups, and embedded parts; suitable for confined workspaces.<\/li>\n<li>Combination shears: Combine cutting and pressing functions for mixed cross-sections.<\/li>\n<li>Hydraulic power packs: Supply the tools efficiently and mobile, including special operations with limited power supply.<\/li>\n<\/ul>\n<h3>Remediation of typical anchor points<\/h3>\n<ul>\n<li>Closure and reprofiling of anchor holes with mineral systems; in multiple layers if required.<\/li>\n<li>Subsequent sealing under moisture exposure with coordinated sealing elements or injections; approach to be defined project-specifically.<\/li>\n<li>Removal of corroded anchor remnants, exposure with pulverizers or split wedges, followed by passivation and reprofiling.<\/li>\n<li>Where leakage paths exist around sleeves or cones, local crack injection and integration into the overall waterproofing strategy are considered.<\/li>\n<\/ul>\n<h2>Areas of application: practical relevance and typical scenarios<\/h2>\n<p>Formwork anchors are encountered in numerous construction tasks. Their handling during deconstruction requires different tool and process decisions depending on the environment and objectives. Typical fields include building construction, infrastructure, and water-retaining structures with strict watertightness and emission limits.<\/p>\n<h3>Concrete demolition and special demolition<\/h3>\n<p>When removing walls with anchor remnants, concrete pulverizers enable selective downsizing and exposure of steel components. Rock and concrete splitters are used to release components with low noise and vibration, for example in inner-city settings or on sensitive existing structures.<\/p>\n<h3>Strip-out and cutting<\/h3>\n<p>During interior strip-out, flush-cut anchor rods often interfere with subsequent sawing or milling. Steel shears or <a href=\"https:\/\/www.darda.de\/en\/product-overview\/multi-cutters\">Multi Cutters<\/a> cold-cut these, and <a href=\"https:\/\/www.darda.de\/en\/product-overview\/hydraulic-power-units\">Hydraulic Power Units<\/a> provide the necessary power. This allows openings and breakthroughs to be produced efficiently without excessive secondary damage.<\/p>\n<h3>Rock demolition and tunnel construction<\/h3>\n<p>For cast-in-place inner linings or tunnels with high water ingress, watertight closure of anchor points is especially important. In deconstruction, concrete pulverizers and splitters serve to open anchor areas in a controlled manner to remediate leaks or create connections without unnecessarily weakening the load-bearing structure.<\/p>\n<h3>Natural stone extraction<\/h3>\n<p>Formwork anchors appear only marginally here, for example in auxiliary constructions for concrete additions or plinths. Knowledge of steel remnants in the stone-concrete composite nevertheless helps align separation strategies: splitters act on natural joints, while steel shears safely cut remaining metallic embedded parts.<\/p>\n<h3>Special operations<\/h3>\n<p>In areas with limited emission budgets (vibration, noise, dust) or in sensitive facilities, low-vibration methods are required. Targeted splitting around anchor points and cold cutting with shears reduces emissions and accelerates subsequent steps.<\/p>\n<h2>Equipment selection by component and objective<\/h2>\n<p>The choice of tool depends on concrete strength, reinforcement and anchor density, accessibility, and the required emission level. Clear sequencing reduces tool changes and speeds up operations.<\/p>\n<ul>\n<li>Thick, heavily reinforced walls with many anchor remnants: concrete pulverizers for the concrete, then steel shears\/Multi Cutters for the anchor rods.<\/li>\n<li>Exposed concrete with dense grid patterns: splitters to release cone areas in a controlled manner; minimal edge spalling.<\/li>\n<li>Confined shafts or interior spaces: compact pulverizers and Multi Cutters with suitable hydraulic power packs.<\/li>\n<li>Assets with high protection requirements: prioritize low-vibration splitting technology, supplemented by cold-cutting methods.<\/li>\n<\/ul>\n<h2>Occupational safety, quality and environment<\/h2>\n<p>Handling formwork anchors requires careful work &#8211; both during concreting and during deconstruction.<\/p>\n<h3>Safety aspects<\/h3>\n<ul>\n<li>Controlled pre-tensioning\/release of anchors; avoid hazards from spring-back.<\/li>\n<li>When cutting or splitting, pay attention to stress states; establish protection zones.<\/li>\n<li>Personal protective equipment, especially cut and splash protection.<\/li>\n<li>Dust and noise control with extraction or water mist where feasible; safe handling of pressurized hydraulic systems.<\/li>\n<\/ul>\n<h3>Quality assurance<\/h3>\n<ul>\n<li>Documentation of anchor arrangement for exposed concrete surfaces.<\/li>\n<li>Inspection and rework of anchor points (watertightness, pull-off strength of reprofiling).<\/li>\n<li>For water-exposed members, coordinated sealing concepts for anchor penetrations.<\/li>\n<li>Mock-ups and trial areas to qualify cone geometry and closure materials before series production.<\/li>\n<\/ul>\n<h3>Environmental aspects<\/h3>\n<ul>\n<li>Low-vibration methods reduce impacts on the surroundings.<\/li>\n<li>Dust and noise reduction through suitable separation methods and hydraulic power packs with demand-based output.<\/li>\n<li>Clean separation of concrete and steel facilitates recycling streams.<\/li>\n<li>Minimized residual metal in deconstruction supports higher recycling rates and reduces downstream sorting effort.<\/li>\n<\/ul>\n<h2>Typical failure patterns and appropriate measures<\/h2>\n<ul>\n<li>Leaking anchor points: Causes range from inadequate closure to material incompatibilities; remedy with adapted reprofiling or injections.<\/li>\n<li>Corrosion of remaining anchor parts: Local exposure with concrete pulverizer\/split wedge, removal or passivation, durable surface protection.<\/li>\n<li>Breakouts at cones: Reprofiling with suitable mortars; for exposed concrete, coordinated color and texture matching.<\/li>\n<\/ul>\n<h2>Practical guide: procedure for removing and closing anchor points<\/h2>\n<ol>\n<li>Investigation: Record drawings, grid, and materials of the anchor components; trial exposure.<\/li>\n<li>Exposure: Locally open the concrete with concrete pulverizers or create controlled cracks with rock and concrete splitters.<\/li>\n<li>Cutting: Cold-cut anchor rods with steel shears or Multi Cutters; flush or recessed, depending on the repair concept.<\/li>\n<li>Preparation: Bondable, clean edges; corrosion protection for remaining metal parts.<\/li>\n<li>Closure: Suitable mortar\/plug; multi-stage sealing build-up if required.<\/li>\n<li>Control: Visual inspection; where applicable, document functional or watertightness testing.<\/li>\n<li>Protection and curing: Observe curing times of repair materials and protect against early drying or washout to ensure durability.<\/li>\n<\/ol>\n<p>This schematic procedure must be adapted to the respective project, the concrete structure, and the requirements. Binding specifications are defined on a project-specific basis by qualified professionals. Consistent documentation supports traceability and future interventions.<\/p>\n<\/div>\n","protected":false},"excerpt":{"rendered":"<p>Formwork anchors are central components in concrete construction: They hold opposing formwork elements in position during concreting, secure the spacing, and transfer fresh concrete pressure. Over a structure&#8217;s lifecycle they concern designers, contractors, and deconstruction teams alike &#8211; from selection and design to later remediation or selective deconstruction. In many <a class=\"moretag\" href=\"https:\/\/www.darda.de\/en\/knowledge\/formwork-anchor\">read more&#8230;<\/a><\/p>\n","protected":false},"author":9,"featured_media":0,"parent":14846,"menu_order":0,"comment_status":"open","ping_status":"open","template":"tmpl\/template-wissen.php","meta":{"_acf_changed":false,"footnotes":"","_members_access_role":[],"_members_access_error":""},"class_list":["post-19707","page","type-page","status-publish","hentry"],"acf":[],"yoast_head":"<!-- This site is optimized with the Yoast SEO plugin v28.5 - https:\/\/yoast.com\/product\/yoast-seo-wordpress\/ -->\n<title>Formwork Anchor in Concrete Construction Guide<\/title>\n<meta name=\"description\" content=\"Guide to the formwork anchor in concrete construction \u2713 components, design, sealing &amp; low-vibration removal.\" \/>\n<meta name=\"robots\" content=\"index, follow, max-snippet:-1, max-image-preview:large, max-video-preview:-1\" \/>\n<link rel=\"canonical\" href=\"https:\/\/www.darda.de\/en\/knowledge\/formwork-anchor\" \/>\n<meta property=\"og:locale\" content=\"en_US\" \/>\n<meta property=\"og:type\" content=\"article\" \/>\n<meta property=\"og:title\" content=\"Formwork Anchor in Concrete Construction Guide\" \/>\n<meta property=\"og:description\" content=\"Guide to the formwork anchor in concrete construction \u2713 components, design, sealing &amp; low-vibration removal.\" \/>\n<meta property=\"og:url\" content=\"https:\/\/www.darda.de\/en\/knowledge\/formwork-anchor\" \/>\n<meta property=\"og:site_name\" content=\"Darda GmbH\" \/>\n<meta property=\"article:publisher\" content=\"https:\/\/www.facebook.com\/DardaDemolition\" \/>\n<meta property=\"article:modified_time\" content=\"2026-05-15T15:56:03+00:00\" \/>\n<meta name=\"twitter:card\" content=\"summary_large_image\" \/>\n<meta name=\"twitter:label1\" content=\"Est. reading time\" \/>\n\t<meta name=\"twitter:data1\" content=\"10 minutes\" \/>\n<script type=\"application\/ld+json\" class=\"yoast-schema-graph\">{\"@context\":\"https:\\\/\\\/schema.org\",\"@graph\":[{\"@type\":\"WebPage\",\"@id\":\"https:\\\/\\\/www.darda.de\\\/en\\\/knowledge\\\/formwork-anchor\",\"url\":\"https:\\\/\\\/www.darda.de\\\/en\\\/knowledge\\\/formwork-anchor\",\"name\":\"Formwork Anchor in Concrete Construction Guide\",\"isPartOf\":{\"@id\":\"https:\\\/\\\/www.darda.de\\\/en#website\"},\"datePublished\":\"2025-12-09T14:24:11+00:00\",\"dateModified\":\"2026-05-15T15:56:03+00:00\",\"description\":\"Guide to the formwork anchor in concrete construction \u2713 components, design, sealing & low-vibration removal.\",\"breadcrumb\":{\"@id\":\"https:\\\/\\\/www.darda.de\\\/en\\\/knowledge\\\/formwork-anchor#breadcrumb\"},\"inLanguage\":\"en-US\",\"potentialAction\":[{\"@type\":\"ReadAction\",\"target\":[\"https:\\\/\\\/www.darda.de\\\/en\\\/knowledge\\\/formwork-anchor\"]}]},{\"@type\":\"BreadcrumbList\",\"@id\":\"https:\\\/\\\/www.darda.de\\\/en\\\/knowledge\\\/formwork-anchor#breadcrumb\",\"itemListElement\":[{\"@type\":\"ListItem\",\"position\":1,\"name\":\"Home\",\"item\":\"https:\\\/\\\/www.darda.de\\\/en\"},{\"@type\":\"ListItem\",\"position\":2,\"name\":\"Knowledge\",\"item\":\"https:\\\/\\\/www.darda.de\\\/en\\\/knowledge\"},{\"@type\":\"ListItem\",\"position\":3,\"name\":\"Formwork anchor\"}]},{\"@type\":\"WebSite\",\"@id\":\"https:\\\/\\\/www.darda.de\\\/en#website\",\"url\":\"https:\\\/\\\/www.darda.de\\\/en\",\"name\":\"Darda GmbH\",\"description\":\"\",\"publisher\":{\"@id\":\"https:\\\/\\\/www.darda.de\\\/en#organization\"},\"alternateName\":\"Abbruchwerkzeuge\",\"potentialAction\":[{\"@type\":\"SearchAction\",\"target\":{\"@type\":\"EntryPoint\",\"urlTemplate\":\"https:\\\/\\\/www.darda.de\\\/en?s={search_term_string}\"},\"query-input\":{\"@type\":\"PropertyValueSpecification\",\"valueRequired\":true,\"valueName\":\"search_term_string\"}}],\"inLanguage\":\"en-US\"},{\"@type\":\"Organization\",\"@id\":\"https:\\\/\\\/www.darda.de\\\/en#organization\",\"name\":\"Darda GmbH\",\"url\":\"https:\\\/\\\/www.darda.de\\\/en\",\"logo\":{\"@type\":\"ImageObject\",\"inLanguage\":\"en-US\",\"@id\":\"https:\\\/\\\/www.darda.de\\\/en#\\\/schema\\\/logo\\\/image\\\/\",\"url\":\"https:\\\/\\\/www.darda.de\\\/wp-content\\\/uploads\\\/2017\\\/09\\\/android-icon-192x192-1.png\",\"contentUrl\":\"https:\\\/\\\/www.darda.de\\\/wp-content\\\/uploads\\\/2017\\\/09\\\/android-icon-192x192-1.png\",\"width\":192,\"height\":192,\"caption\":\"Darda GmbH\"},\"image\":{\"@id\":\"https:\\\/\\\/www.darda.de\\\/en#\\\/schema\\\/logo\\\/image\\\/\"},\"sameAs\":[\"https:\\\/\\\/www.facebook.com\\\/DardaDemolition\",\"https:\\\/\\\/www.instagram.com\\\/darda_demolition\",\"https:\\\/\\\/www.youtube.com\\\/user\\\/DardaGmbH\",\"https:\\\/\\\/www.xing.com\\\/pages\\\/darda-gmbh\",\"https:\\\/\\\/de.linkedin.com\\\/company\\\/darda-gmbh\"]}]}<\/script>\n<!-- \/ Yoast SEO plugin. -->","yoast_head_json":{"title":"Formwork Anchor in Concrete Construction Guide","description":"Guide to the formwork anchor in concrete construction \u2713 components, design, sealing & low-vibration removal.","robots":{"index":"index","follow":"follow","max-snippet":"max-snippet:-1","max-image-preview":"max-image-preview:large","max-video-preview":"max-video-preview:-1"},"canonical":"https:\/\/www.darda.de\/en\/knowledge\/formwork-anchor","og_locale":"en_US","og_type":"article","og_title":"Formwork Anchor in Concrete Construction Guide","og_description":"Guide to the formwork anchor in concrete construction \u2713 components, design, sealing & low-vibration removal.","og_url":"https:\/\/www.darda.de\/en\/knowledge\/formwork-anchor","og_site_name":"Darda GmbH","article_publisher":"https:\/\/www.facebook.com\/DardaDemolition","article_modified_time":"2026-05-15T15:56:03+00:00","twitter_card":"summary_large_image","twitter_misc":{"Est. reading time":"10 minutes"},"schema":{"@context":"https:\/\/schema.org","@graph":[{"@type":"WebPage","@id":"https:\/\/www.darda.de\/en\/knowledge\/formwork-anchor","url":"https:\/\/www.darda.de\/en\/knowledge\/formwork-anchor","name":"Formwork Anchor in Concrete Construction Guide","isPartOf":{"@id":"https:\/\/www.darda.de\/en#website"},"datePublished":"2025-12-09T14:24:11+00:00","dateModified":"2026-05-15T15:56:03+00:00","description":"Guide to the formwork anchor in concrete construction \u2713 components, design, sealing & low-vibration removal.","breadcrumb":{"@id":"https:\/\/www.darda.de\/en\/knowledge\/formwork-anchor#breadcrumb"},"inLanguage":"en-US","potentialAction":[{"@type":"ReadAction","target":["https:\/\/www.darda.de\/en\/knowledge\/formwork-anchor"]}]},{"@type":"BreadcrumbList","@id":"https:\/\/www.darda.de\/en\/knowledge\/formwork-anchor#breadcrumb","itemListElement":[{"@type":"ListItem","position":1,"name":"Home","item":"https:\/\/www.darda.de\/en"},{"@type":"ListItem","position":2,"name":"Knowledge","item":"https:\/\/www.darda.de\/en\/knowledge"},{"@type":"ListItem","position":3,"name":"Formwork anchor"}]},{"@type":"WebSite","@id":"https:\/\/www.darda.de\/en#website","url":"https:\/\/www.darda.de\/en","name":"Darda GmbH","description":"","publisher":{"@id":"https:\/\/www.darda.de\/en#organization"},"alternateName":"Abbruchwerkzeuge","potentialAction":[{"@type":"SearchAction","target":{"@type":"EntryPoint","urlTemplate":"https:\/\/www.darda.de\/en?s={search_term_string}"},"query-input":{"@type":"PropertyValueSpecification","valueRequired":true,"valueName":"search_term_string"}}],"inLanguage":"en-US"},{"@type":"Organization","@id":"https:\/\/www.darda.de\/en#organization","name":"Darda GmbH","url":"https:\/\/www.darda.de\/en","logo":{"@type":"ImageObject","inLanguage":"en-US","@id":"https:\/\/www.darda.de\/en#\/schema\/logo\/image\/","url":"https:\/\/www.darda.de\/wp-content\/uploads\/2017\/09\/android-icon-192x192-1.png","contentUrl":"https:\/\/www.darda.de\/wp-content\/uploads\/2017\/09\/android-icon-192x192-1.png","width":192,"height":192,"caption":"Darda GmbH"},"image":{"@id":"https:\/\/www.darda.de\/en#\/schema\/logo\/image\/"},"sameAs":["https:\/\/www.facebook.com\/DardaDemolition","https:\/\/www.instagram.com\/darda_demolition","https:\/\/www.youtube.com\/user\/DardaGmbH","https:\/\/www.xing.com\/pages\/darda-gmbh","https:\/\/de.linkedin.com\/company\/darda-gmbh"]}]}},"_links":{"self":[{"href":"https:\/\/www.darda.de\/en\/wp-json\/wp\/v2\/pages\/19707","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.darda.de\/en\/wp-json\/wp\/v2\/pages"}],"about":[{"href":"https:\/\/www.darda.de\/en\/wp-json\/wp\/v2\/types\/page"}],"author":[{"embeddable":true,"href":"https:\/\/www.darda.de\/en\/wp-json\/wp\/v2\/users\/9"}],"replies":[{"embeddable":true,"href":"https:\/\/www.darda.de\/en\/wp-json\/wp\/v2\/comments?post=19707"}],"version-history":[{"count":2,"href":"https:\/\/www.darda.de\/en\/wp-json\/wp\/v2\/pages\/19707\/revisions"}],"predecessor-version":[{"id":27461,"href":"https:\/\/www.darda.de\/en\/wp-json\/wp\/v2\/pages\/19707\/revisions\/27461"}],"up":[{"embeddable":true,"href":"https:\/\/www.darda.de\/en\/wp-json\/wp\/v2\/pages\/14846"}],"wp:attachment":[{"href":"https:\/\/www.darda.de\/en\/wp-json\/wp\/v2\/media?parent=19707"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}